Holy Sweet Baby Jesus !
Ok, I’m a newbie somewhat and bought this 870 at a shop and it looked pretty good, but I decided to clean it before going shooting (Know your gun). THANK GOODNESS!!!!
Lesson 1: don’t trust a gun shop to sell you a clean gun.
I’ve worked on car engines that weren’t this dirty.
I had to spray brake clean in the trigger group and bolt to get enough crap out to then clean it enough to oil it. Still needs cleaning and inspection by a Pro before I go shooting as I don’t know enough (or proper tools) to take apart the bolt and trigger group.
How many rounds without cleaning does it take to wear the bluing off a mag tube? And look at that plastic follower
Attachments
7B6667E9-DA90-4798-9FD3-D390BCA95317.jpeg (485.9 KiB) Viewed 6448 times
079A3FA1-C9DA-4EA6-9944-D9C1FAA3F2C4.jpeg (407.49 KiB) Viewed 6448 times
65B2D4C4-CDE0-475E-B26A-0C605A33954B.jpeg (188.46 KiB) Viewed 6448 times
Well, the good news is that you did clean it, so now we know it's clean. Some folks never clean their guns, and it's best for some because I know many who could not reassemble even one as simple as an 870.
Imperious Moderatus
Retired USN
NRA Life ; NAHC Life Pain heals, chicks dig scars.....glory -- lasts forever!
Scorpion8 wrote: ↑Sat Aug 15, 2020 4:23 pm
Well, the good news is that you did clean it, so now we know it's clean. Some folks never clean their guns, and it's best for some because I know many who could not reassemble even one as simple as an 870.
Yes, some people don’t have mechanical skills (my wife ) , but I can’t imagine even an 870 not jamming Or having a misfire once in a while if it’s this filthy. I had to struggle to get the trigger group out of the receiver.
I have to admit i dont clean mine often either. About the only time i clean one is when i look in it and think, “damn i need to clean this” The massive amount of corrosive.303 and 8mm ammo i have fired over the years as turned me against much cleaning.
The devil danced as he went down, in the hail of arrows comin' Out on the wild Montana ground, Custer died a-runnin'.
Banshee wrote: ↑Sat Aug 15, 2020 7:13 pm
I have to admit i dont clean mine often either. About the only time i clean one is when i look in it and think, “damn i need to clean this” The massive amount of corrosive.303 and 8mm ammo i have fired over the years as turned me against much cleaning.
I think everyone slacks off some, but this thing was just stupidly bad. Bad enough that it’s fouled the right side shell latch bad enough that I need to have it repaired by a gun smith (Jams repeatedly).
I occasionally buy shotguns on line where you can’t inspect them before purchase. Boy, I’ve seen filth similar to what you found.
One that I bought was a 1949 870 Wingmaster about 3 years ago. The barrel was very clean, but it took me almost 2 days to get the receiver, trigger group, and bolt assembly clean!! Carbon residue was literally caked in layers inside the receiver. I ruined 2 brass cleaning hand brushes in the process. And it stunk after the cleaning process started. I soaked most of the parts in Hoppes solvent overnight. That helped. I used MPro7 inside of the receiver. It took a lot of scrubbing.
I finally got it good and clean. It’s now in good shape and shoots well. I took it to the trap range with me and shot one round with it. I scores 21 with it, which is about my average with my designated trap gun. It’s a good gun.
The Rattler wrote: ↑Wed Sep 09, 2020 1:32 am
I occasionally buy shotguns on line where you can’t inspect them before purchase. Boy, I’ve seen filth similar to what you found.
One that I bought was a 1949 870 Wingmaster
I finally got it good and clean. It’s now in good shape and shoots well. I took it to the trap range with me and shot one round with it. I scores 21 with it, which is about my average with my designated trap gun. It’s a good gun.
1949 Wingmaster is a nice find even with all the cleaning needed.
I was eyeing a pump (don’t recal brand) from about 1930 or so. Wanted to buy it just to have such a lovely old gun.
Sadly I don’t have a lot of extra funds for fun stuff.
I bought a 1960 Wingmaster on line a couple of years ago that was extremely dirty like that. The barrel was clean but the receiver, trigger group, & bolt appeared to have never been cleaned. It took me 2 days to clean it. The carbon build up had hardened. The butt plate was so dirty with decades of packed mud in it’s cracks, that it took a couple of hours to clean.
After immersing various parts in Hoppes #9 and hours of scrubbing with a bronze brush, the brush was ruined but the receiver and its innards were clean. The gun operates well and is a good shooter. It has many good years left.
) , but I can’t imagine even an 870 not jamming Or having a misfire once in a while if it’s this filthy. I had to struggle to get the trigger group out of the receiver.
The massive amount of corrosive.303 and 8mm ammo i have fired over the years as turned me against much cleaning. 